Journal Articles
Permanent URI for this collection
Browse
Recent Submissions
Item Open Access Evaluation of Millet Extract as Green Inhibitor for AA6063 Corrosion in 1 M KCl: From Electrochemical Studies to Optimisation(Asian Journal of Chemistry, 2026-05-31) FAYOMI Ojo S. I; OGBUOZOBE Onyeka G.; MIN Ho SoonThis study presents a comprehensive evaluation of millet extract as a green corrosion inhibitor for the protection of AA6063 in a 1 M KCl solution medium. The research integrates multiple electrochemical techniques, including open circuit potential (OCP) measurements and linear sweep voltammetry (LSV), alongside detailed adsorption studies. These are further complemented by the application of response surface methodology (RSM) to enhance and optimize the inhibitor’s performance. A central composite design (CCD) was strategically employed to systematically vary key experimental parameters, specifically, the concentration of millet extract and the operating solution temperature. The electrochemical investigations provided deeper insights into the underlying inhibition mechanism, while the RSM framework enabled the identification of optimal operating conditions for corrosion control. The resulting second-order polynomial model was rigorously validated through analysis of variance (ANOVA), which confirmed the statistical significance and strong influence of both concentration and temperature on the corrosion rate. The optimal conditions were determined at a concentration of 0.284 g and a temperature of 33.56 ºC, resulting in a low corrosion rate of 0.332 mm yr–1. This study concludes that millet extract is an effective and environmentally friendly corrosion inhibitor, offering a viable, sustainable alternative to conventional chemical inhibitors in corrosion prevention strategies.Item Open Access Achieving a super-strengthening functional composite coating from ZnO doped snail shell particulate for mitigation of mild steel towards improved microstructural, corrosion, and opto-electrical properties(Elsevier, 2024-10-01) FAYOMI Ojo S.I.Long-lasting protective coatings are essential, particularly under harsh operating conditions. Surface coatings provide a flexible alternative; electrodeposition is becoming an established approach for protecting steel. The intent of this study is to determine how effectively zinc oxide (ZnO) coatings for mild steel corrosion protection effect when integrated with snail shell particle (SSP). The experimental setup consisted of producing a coating bath with ZnO and SSP particles, then electrodeposting the mixture under conditions onto polished steel surfaces. The created coatings were subjected to an array of tests, including electrical conductivity and resistivity testing, morphological analysis using SEM/EDS, corrosion testing in a 1M HCl solution, hardness testing. The findings show that when SSP content increases, steel corrosion rates significantly decrease, suggesting improved corrosion resistance from 21.85(mm/yr) to 12.80(mm/yr), and polarization resistance of 4.47E+01(Ω) to 8.00E+01(Ω). Morphological examination shows that SSP particles are dispersed throughout the coating matrix, which promotes adhesion and stability. Also, coatings with more SSP show better electrical characteristics. Overall, the study shows how ZnO-SSP coatings can shield mild steel components from adverse conditions and have prospective uses in sectors where surfaces resistant to corrosion are needed.Item Open Access Mechanical and Structural Investigation of Zn-MnO2 Coating on Mildsteel(Scientific Net, 2024-11-01) DEREK Alima O.; FAYOMI Ojo S.I.; ATIBA Joshua O.Abstract: Failure in manufacturing industries is a worldwide concern and it occurs most often at elevated temperatures and pressure. Acid, gases, and steam are known to be corrosion and stress-induced propagators resulting in incessant catastrophes. More so, material failure can be due to the substrate material used in the coating while substrate failure can further be classified into the substrate morphology, surface chemistry as well as contamination. Thus, the study developed a multifaceted layer of zinc barrier coating via the electrodeposition technique and observe its response by characterizing the developed coating. The mild steel plate, Zn and MnO2 were procured and characterized according to the ASTM standard. Mild steel of dimension 60×30×2 mm was sectioned and polished using varying sizes of abrasives. The result of the coating thickness showed that Zn-6MnO2 had a weight gain of 0.30g. Zn-12MnO2 was observed to have excellent corrosion performance compared to the as-received and the other formulations of Zn-MnO2 with a corrosion resistance of 2.117 mm/year. The SEM image of Zn-MnO2 showed aggregates of clustered grains, thus, no possible fracture lines were observed on the coating surface. Zn-12MnO2 exhibited a hardness value of 252.72 BHN. Additionally, the EDS of the coatings revealed significant elements that helped in the corrosion performance and hardness properties of the coatings.Item Open Access Corrosion and Surface Modification of Hybridized Seashell Composite on AA6063 Alloy for Advance Application(Asian Journal of Chemistry, 2025-08-30) FAYOMI Ojo S.I.; AJIBOLA Otitolaye A.; MIN Ho Soon; OLUWASEGUN Kunle M.Abstract This study focuses on utilizing abundantly available seashell ash by dispersing it in AA6063 alloy to form composites. A new aluminium metal matrix composite was developed by reinforcing AA 6063 alloy with particles of seashell ash as reinforcement materials in varying percentages (0, 10, 20, 30, 40 wt.%). The samples were prepared by using the stir casting method. The microstructural characterizations were carried out using optical microscopy and the scanning electron microscope (SEM), revealing particle shape and size descriptions for the composite microstructural features. The results indicate that the composite materials exhibit relatively larger and more uniformly distributed grain sizes compared to the base material. The outcomes demonstrate a significant improvement in the tensile strength and hardness of the composites, accompanied by a decrease in corrosion rates. The best samples display a 90.95% increase in tensile strength, a 38.01% increase in hardness and a 71.5% decrease in corrosion rate in an HCl environment, along with a 46.7% decrease in a NaCl environment. Furthermore, there is a 207.7% increase in impact strength in the sample reinforced with 20 wt.% of seashell ash. Overall, the AA-SS composite with 20% wt. seashell ash exhibits the most favourable properties, featuring a 90.95% increase in tensile strength, a 38.01% increase in hardness and a lower corrosion rate when compared to the control sample.